Pages


Monday, April 15, 2013

WSRM---LEDlights Application Notes!


HERE IS LIGHT!HERE IS LIFE!


WSRM---LEDlights Application Notes!


Eye Protection - LEDs are very bright. DO NOT look directly into the LED light. The light can be intense enough to injure human eyes.
diagram of a white LED

How does a LED work?

This is a very simple explanation of the
construction and function of LEDs. White LEDs
 need 3.6VDC and use approximately 30 milliamps
of current, a power dissipation of 100 milliwatts.
 The positive power is applied to one side of the
 LED semiconductor through
 a lead (1 anode) and a whisker (4). The other
side
 of the semiconductor is attached to the top of the anvil (7) that is the
negative power lead (2 cathode). It is the chemical makeup
 of the LED semiconductor (6) that determines the color of the light the
 LED produces. The epoxy resin enclosure (3 and 5) has three functions.
It is designed to allow the most light to escape from the semiconductor,
it focuses the light (view angle), and it protects the LED semiconductor
 from the elements. As you can see, the entire unit is totally embedded
 in epoxy. This is what make LEDs virtually indestructible. There are no
loose or moving parts within the solid epoxy enclosure.
Therefore, a light-emitting diode (LED) is essentially a PN junction semiconductor diode that emits light when current is applied. By definition, it is a solid-state device that controls current without heated filaments and is therefore very reliable. LED performance is based on a few primary characteristics:
wave length in nm

LED Colors

LEDs are highly monochromatic, emitting a pure color in a narrow frequency range. The color emitted from an LED is identified by peak wavelength (lpk) and measured in nanometers (nm ). 

Peak wavelength is a function of the LED chip material. Although process variations are ±10 NM, the 565 to 600 NM wavelength spectral region is where the sensitivity level of the human eye is highest. Therefore, it is easier to perceive color variations in yellow and amber LEDs than other colors.
LEDs are made from gallium-based crystals that contain one or more additional materials such as phosphorous to produce a distinct color. Different LED chip technologies emit light in specific regions of the visible light spectrum and produce different intensity levels

Comparison of chip technologies for wide-angle, non-diffused LEDs

LED
Color
Standard BrightnessHigh Brightness
Chip
Material
lpk
(NM)
Iv
(mcd)
Viewing
Angle
Chip
Material
lpk
(NM)
Iv3(mcd)Viewing
Angle
Red
GaAsP/GaP
635
120
35
AS AlInGaP
635
900
30
Orange
GaAsP/Gap
605
90
30
AS AlInGaP
609
1,300
30
Amber
GaAsP/Gap
583
100
35
AS AlInGaP
592
1,300
30
Yellow
Gap
570
160
30
--
--
--
--
Green
Gap
565
140
24
GaN
520
1,200
45
Turquoise
--
--
--
--
GaN
495
2,000
30
Blue
--
--
--
--
GaN
465
325
45

White LED Light

When light from all parts of the visible spectrum overlap one another, the additive mixture of colors appears white. However, the eye does not require a mixture of all the colors of the spectrum to perceive white light. Primary colors from the upper, middle, and lower parts of the spectrum (red, green, and blue), when combined, appear white. To achieve this combination with LEDs requires a sophisticated electro-optical design to control the blend and diffusion of colors. Variations in LED color and intensity further complicate this process.
Presently it is possible to produce white light with a single LED using a phosphor layer (Yttrium Aluminum Garnet) on the surface of a blue (Gallium Nitride) chip. Although this technology produces various hues, white LEDs may be appropriate to illuminate opaque lenses or backlight legends. However, using colored LEDs to illuminate similarly colored lenses produces better visibility and overall appearance.
diagram of LED

Intensity

LED light output varies with the type of chip, encapsulation, efficiency of individual wafer lots and other variables. Several LED manufacturers use terms such as "super-bright," and "ultra-bright" to describe LED intensity. Such terminology is entirely subjective, as there is no industry standard for LED brightness. The amount of light emitted from an LED is quantified by a single point, on-axis luminous intensity value (Iv). LED intensity is specified in terms of millicandela (mcd). This on-axis measurement is not comparable to mean spherical candlepower (MSCP) values used to quantify the light produced by incandescent lamps.

Luminous intensity

is roughly proportional to the amount of current (If) supplied to the LED. The greater the current, the higher the intensity. Of course, there are design limits. Generally, LEDs are designed to operate at 20 milliamps (mA). However, operating current must be reduced relative to the amount of heat in the application. For example, 6-chip LEDs produce more heat than single-chip LEDs. 6-chip LEDs incorporate multiple wire bonds and junction points that are affected more by thermal stress than single-chip LEDs. Similarly, LEDs designed to operate at higher design voltages are subject to greater heat. LEDs are designed to provide long-life operation because of optimal design currents considering heat dissipation and other degradation factors.

Eye Safety Information

The need to place eye safety labeling on LED products is dependent upon the product design and the application. Only a few LEDs produce sufficient intensity to require eye safety labeling. However, for eye safety, do not stare into the light beam of any LED at close range
diagram of LED

Visibility

Luminous intensity (Iv) does not represent the total light output from an LED. Both the luminous intensity and the spatial radiation pattern (viewing angle) must be taken into account. If two LEDs have the same luminous intensity value, the lamp with the larger viewing angle will have the higher total light output.
Theta one-half (q½) is the off-axis angle where the LED's luminous intensity is half the intensity at direct on-axis view. Two times q½ is the LEDs' full viewing angle; however, light emission is visible beyond the q½ point. Viewing angles listed in this catalog are identified by their full viewing angle (2q½ °).
LED viewing angle is a function of the LED chip type and the epoxy lens that distributes the light. The highest luminous intensity (mcd rating) does not equate to the highest visibility. The light output from an LED chip is very directional. A higher light output is achieved by concentrating the light in a tight beam. Generally, the higher the mcd rating, the narrower the viewing angle.
The shape of the encapsulation acts as a lens magnifying the light from the LED chip. Additionally, the tint of the encapsulation affects the LED's visibility. If the encapsulation is diffused, the light emitted by the chip is more dispersed throughout the encapsulation. If the encapsulation is non-diffused or water clear, the light is more intense, but has a narrower viewing angle. Non-diffused and water clear LEDs have identical viewing angles; the only difference is, water clear encapsulations do not have a tint to indicate color when the LED is not illuminated.
Overall visibility can be enhanced by increasing the number of LED chips in the encapsulation, increasing the number of individual LEDs, and utilizing secondary optics to distribute light. To illustrate, consider similar red GaAlAs LED chip technology in four different configurations:
diagram of LEDs
In each case, the amount of visible light depends on how the LED is being viewed. The single chip may be appropriate for direct viewing in competition with high ambient light. The 6-chip may be better suited to backlight a switch or small legend, while the cluster or lensed LED may be best to illuminate a pilot light or larger lens.

Operating Life

Because LEDs are solid-state devices they are not subject to catastrophic failure when operated within design parameters. DDP® LEDs are designed to operate upwards of 50,000 hours at 25°C ambient temperature. Operating life is characterized by the degradation of LED intensity over time. When the LED degrades to half of its original intensity after 50,000 hours it is at the end of its useful life although the LED will continue to operate as output diminishes. Unlike standard incandescent bulbs, DDP® LEDs resist shock and vibration and can be cycled on and off without excessive degradation.

Voltage/Design Current

LEDs are current-driven devices, not voltage driven. Although drive current and light output are directly related, exceeding the maximum current rating will produce excessive heat within the LED chip due to excessive power dissipation. The result will be reduced light output and reduced operating life.
LEDs that are designed to operate at a specific voltage contain a built-in current-limiting resistor. Additional circuitry may include a protection diode for AC operation or full-bridge rectifier for bipolar operation. The operating current for a particular voltage is designed to maintain LED reliability over its operating life.

Precautions While Working With LEDs

General
We cannot assume any responsibility for any accident or damage caused when the products are used beyond the maximum ratings specified herein. These pages are for information only and are the user assumes all responsibility and risk.
The user of these products must confirm the performance of the LEDs after they are actually assembled into the user's products/systems. It is strongly advised that he user design fail-safe products/systems. We will not be responsible for legal matters which are caused by the malfunction of these products/systems.

Static Electricity and Surge

Static electricity and surge damage LEDs. It is recommended to use a wrist band or anti-electrostatic glove when handling the LEDs. All devices, equipment and machinery must be electrically grounded.

lead forming ledsLEAD Forming:

The leads should be bent at a point at least 3mm from the epoxy resin of the LEDs.
Bending should be performed with the base firmly fixed by means of a jig or radio pliers.
Mounting Method for LEDsDo not bend

Mounting Method:

The leads should be formed so they are aligned exactly with the holes on the PC board. This will eliminate any stress on the LEDs.
Use LEDs with stoppers or resin spacer to accurately position the LEDs. The epoxy resin base should not be touching the PC board when mounting the LEDs. Mechanical stress to the resin may be caused by the warping of the PC board when soldering. The LEDs must not be designed into a product or system where the epoxy lens is pressed into a plastic or metal board. The lens part of the LED must not be glued onto plastic or metal. The mechanical stress to the leadframe must be minimized.

Soldering

Solder the LEDs no closer than 3mm from the base of the epoxy resin.
For solder dipping, it may be necessary to fix the LEDs for correct positioning. When doing this, any mechanical stress to the LEDs must be avoided.
When soldering, do not apply any mechanical force to the leadframe while heating.
Repositioning after soldering must be avoided.
Soldering conditions:
Soldering IronDip SolderingReflow Soldering
Lamp LED
300degC(max), 3sec(max)
260degC(max), 5sec(max)
Not allowed.
Chip LED
300degC(max), 3sec(max) with Twin Head iron
Not allowed.
chip LED

Cleaning

Avoid exposure to chemicals as they may attack the LED surface and cause discoloration. When washing is required, "isopropyl alcohol" is to be used.
The influence of ultrasonic cleaning on the LEDs differs depending on factors such as oscillator output and the way in which the LEDs are mounted. Therefore, ultrasonic cleaning should only be performed after making certain that it will not cause any damage.

Emission color

LED emission wavelengths vary. LEDs are classified by emission color into different ranks. When a large volume of LEDs are purchased, LEDs with different color ranks will be delivered

Packaging

The leadframes of the LEDs are coated with silver. Care must be taken to maintain a clean storage atmosphere. If the LEDs are exposed to gases such as hydrogen sulfide, it may cause discoloration of the leadframes.
Moistureproof packing is used to keep moisture away from the chip type LEDs. When storing chip type LEDs, please use a sealable package with a moisture absorbent material inside.

LED Cluster Lamp and LED Dot Matrix Unit

Assembly
Please refer to the recommended distance between the leads when designing lead holes on the PC board.
Close attention must be paid on the correct positioning of O-rings and other water proof seals when assembling products/systems.
LEDs are vulnerable to static electricity. When handling the LEDs, necessary precautions regarding static electricity must always be taken into consideration.

Installation of LEDs

Make certain that the lead position and polarity are correct when installing the LEDs.
The interface cable must be as short as possible.
The power supply and ground line must be selected according to their current capacity.

Heat Dissipation

When many LEDs are mounted into a small area, heat generation must be taken into consideration. If there is a possibility that the ambient temperature may exceed 60 degrees centigrade, some kind of forced cooling system will be needed
The ambient operating temperature must be taken into consideration when a product/ system is being designed. There are certain limits to maximum current, at certain temperatures which must be kept in mind.

Handling

When the surface of the LEDs must be cleaned, the LEDs should be wiped softly with detergent. The surface may be damaged and the effect of the lens may be reduced with violent scrubbing.

Others

EMI countermeasures must be taken as a system.
When instantaneous power failure, or a current surge by lightning stops the controller at abnormal conditions, the abnormally high electric current may continue running through the LEDs for an extended period of time. This can damage the LEDs in the system. Circuit protection against abnormally high current must be built into the system to protect against this.
http://zgledn.yglm.mobi/
SALES CONTACT
ITALY
 NETHERLAND
Amsterdam


Sunday, April 14, 2013

WSRM---LEDlights save enery in every space in the worldwide!


HERE IS LIGHT!HERE IS LIFE!


WSRM---LEDlights save enery in every space in the worldwide!
We’re teaching how to go green and save energy with the lights in every space we can think of! Click here to browse the entire energy-efficient lighting series.


The right lighting is essential for any museum. Each exhibit needs a lighting scheme that will preserve the artistic, historical, or scientific integrity of the articles on display. And it just has to look good too.
If you’ve already landed on a lighting scheme that works for your museum, you’re probably apprehensive to change it, even if you could save money.
Good news: Upgrading your museum lighting is easier than you might think. There are a ton of small, barely noticeable changes you can make to your museum lighting that will save you energy. Also, newer energy-efficient lighting options may actually provide more versatile, higher quality light for your displays.
Let’s get started, shall we?
Small Changes:  
1. Guide Lights
If you have dark areas in your museum – night simulations or moody displays – you’ll always need small guide lights to keep your visitors safe and comfortable. These are things like step lights along staircases and rope lights along pathways or handrails. These lights will never add to or take away from the integrity of your display. They’re just there. So why not save a little energy with them?
The most energy-efficient step lights and guide lights you can find on the market are probably LEDs. They’ll last much longer than older incandescent lights and most fluorescent lights, and they’ll produce the same brightness while only using a fraction of the energy.
2. Exit Signs
Exit signs are necessary features in any museum, but it’s not necessary that you use a lot of energy to operate them. A good LED exit sign only costs $2 to operate every year. Compare that to the $39 it costs to run a single incandescent exit sign. The LED will pay for itself within a year!
If you’re even more ambitious about saving energy, you can opt for photoluminescent exit signs. They’re made with a special material that absorbs ambient light and emits it when the lights go dark. No maintenance or electricity required.
3. Light Bulbs
You probably use regular old light bulbs here and there in your museum – in wall sconces along the hallways, in table lamps at reception, or in hanging light fixtures in the lobby. Switching these out for energy-efficient halogen lamps or LEDs will help cut down that energy bill more than you think.
A good LED light bulb might use as little as 13% of the energy it takes to power an incandescent light bulb of equivalent brightness. Energy-efficient halogen lamps are the perfect choice when you need that unmistakable crisp halogen light. They provide the same quality light while using 33% less energy than a regular halogen lamp.
4. Occupancy Sensors
The best way to save energy anywhere is to simply turn off the lights.
But, this is impossible and frankly dangerous for a busy public place like a museum, but it’s a strategy to consider for utilitarian areas of the building like bathrooms and storage closets. Putting those lights onoccupancy/vacancy sensors will make sure they turn on when needed, and off when there’s nobody around.
Bigger Changes: 
1. Ceiling Lights
If using recessed can lights for overhead lighting in your museum, think about using them with LED retrofit modules. It’s one of the easiest ways to save energy on a grander scale, and the light provided by these fixtures matches the quality of incandescent or halogen lights.
They last between 35,000 and 50,000 hours, and use lass than 25% of the energy consumed by their incandescent counterparts.
2. Accent Lights
In rooms with bold architecture – coves, niches, columns, signs, or even sculptures – you probably already use some kind of light as an accent. Not only will replacing these with LEDs save you more energy and require less maintenance, they’ll also give you more creative freedom when planning exhibits and events.
For example, if you light your coves with color changing LED tape lights, you can keep them bright white during the normal hours or change the hue  for an evening benefit, holiday, or special showcase. LEDs are one of the most low-profile light sources, so the fixtures will never distract from the museum’s overall aesthetic.
3. Display Lights
Of course, the most important lights in a museum are the display lights. They serve your museum’s most essential purpose. They dictate how visitors see the things you display. So why change your display lights if you already love how they look?
Well, LED display lights help you save energy AND they’ll be safer for the things on display. Yes, by now you know LEDs use much less energy to achieve the same results as older light sources, but you might not know that LEDs won’t expose your artwork, artifacts, or sensitive object to any harmful UV light. UV light can easily degrade delicate objects. LEDs also run cooler than other light sources, especially halogen, which can be another benefit when lighting sensitive material.
To learn more, check out our museum lighting page here.

http://zgledn.yglm.mobi/
SALES CONTACT
ITALY
 NETHERLAND
Amsterdam




Saturday, April 13, 2013

WSRM---How to Choose Under Cabinet Lighting!


HERE IS LIGHT!HERE IS LIFE!


WSRM---How to Choose Under Cabinet Lighting!

If you’re only going to choose just one lighting feature to add your kitchen, make it under cabinet lighting.  It provides task lighting for your countertops to make them ideal for food preparation and cooking, it illuminates the backsplash on your wall to create beautiful accent lighting, and it can also be used as night lighting for your kitchen.  Once you install under cabinet lighting, you’ll never want to go back.
Many lighting designers talk about creating “layers of light” for your kitchen.  Under cabinet lighting serves as a crucial “layer” for great design.
That being said, there are a ton of options to choose from.  How do you know what style of under cabinet lighting is right for your kitchen?  Hopefully, this guide will make it a little easier to make your selection.
It’s a good idea to choose your light source first.
1. Fluorescent, Xenon, or LED?
Fluorescent under cabinet lights are the most energy efficient in providing a given amount of light.  Moreover, fluorescent light sources give off very little heat.  This is a great feature depending on what is stored in the cabinet immediately above the under cabinet fixture or, perhaps, what is lying 12 to 18 inches below the light.  While most fluorescent fixtures cannot be dimmed, they can be a wonderful, inexpensive option.  In addition, our Microfluorescent Fixtures or Fluorescent Swivel Sticks are probably the easiest products to install – a definite plus.

Xenon lights are not quite as energy efficient and do give off some heat but they have full dimming capacity, and they give off an attractive warm light.  (If you love the warm glow of an incandescent light bulb, xenon under cabinet lights are for you).  While they’re not cool to the touch, the amount of heat emitted is still substantially lower than halogen lights.  Heat output can be an important consideration with under cabinet lighting since you’re often installing the lights directly on the underside of food storage cabinets – and above any produce sitting out on the counter.  For this reason, we don’t sell halogen under cabinet lights.
2. Puck or Linear?If you’re looking for the most energy efficient option, go with LEDs.  Although most LEDs cannot be dimmed, some fixtures have two levels of brightness which allows for some flexibility. LEDs are also cool to the touch and will last for 50,000 hours before needing replacement bulbs (that’s almost six years).  The initial price tag is a bit more expensive but if you consider your future savings in energy, LED under cabinet lights start to make a lot of sense.  They also give off a brilliant white light that is very appealing for kitchen design.
The style of the fixture is another consideration.  We usually recommend installing linear under cabinet lightsbecause they provide uniform, well-distributed light for the entire countertop and eliminate shadows.  However, a number of people prefer the style of under cabinet puck lights for the kitchen, which create pools of light in more focused areas.  Either type of light works fine, this is really just a matter of preference.
3. Recessed or Surface mount?
A lot of people assume that non-recessed under cabinet lights will have fixtures jutting out unattractively from underneath the cabinets.  This really isn’t the case –most of the surface-mount options are so thin that you’d have to literally stick your head underneath the cabinet and look up to see the actual fixture.  The good news is that it’s hard to go wrong on this decision.  If you absolutely love the seamless look of recessed lighting – even when it’s hidden – check out the recessed under cabinet lights (but keep in mind that all of the recessed options are also puck lights).




There’s a much larger selection of surface mount under cabinet lights.  Themost low-profile surface mount under cabinet lights are the Microfluorescent T4 Light Fixtures.  The Xenon Line Voltage Thin Under Cabinet Task Lights are also very low-profile and are some of our most popular under cabinet lights.  Our VP, Chris Johnson, actually installed these into his home.  Check out thisblog post to see before and after pictures if you’re interested.
4. Hardwire or Plug-in?
Lighting fixtures that are “hardwired” are connected directly to the power source using a ROMEX® wire (this is what is used behind your walls to wire your entire house).  Plug-in under cabinet lights, of course, require you to plug in a cord to your nearest electrical outlet.  Decide what your preference is for type of installation and placement – if there’s not a well-placed outlet in your kitchen, you’ll probably want to go with hardwire.  A number of our under cabinet lights can be set up to be either hardwire or plug-in, but there are a few that do not have both options, so just check out the product listings of hardwire under cabinet lighting and plug-in under cabinet lighting.
The FAQs tab on our under cabinet lighting page has some really helpful information to explain the options even further.  Good luck installing your under cabinet lights, and don’t forget to tell us how it goes!  Comment on this post with any questions and/or post your photos of your recent lighting project on our Facebook page
http://zgledn.yglm.mobi/
SALES CONTACT
ITALY
 NETHERLAND
Amsterdam





Friday, April 12, 2013

WSRM---EUROPE LEDlights technology question and answers!



HERE IS LIGHT!HERE IS LIFE!


WSRM---EUROPE LEDlights technology question and answers!

Europe has always been ahead of the US when it comes to energy efficiency and green building design, so it's no surprise that our friends across the pond have been enjoying the benefits of LED lighting for a while now. However, there are still plenty of misconceptions and false information out there when it comes to LEDs. Yes, they are a lot more efficient than incandescents and even CFLs, but you probably aren't aware of all the advances that make LEDs a viable option for lighting your home.

 Dr. Stephen Shephard is our customer in Spain that supplies WSRM---LEDlights for use in the home, specifically in kitchens. His customer asked him a few questions about LED technology and best uses:

Q. LEDs were very directional in the past, but that's not so anymore. Are these lamps now adequate for lighting an entire room?A. While LEDs are still directional, there have been several approaches to combat this to create beam angles similar to normal spot lights and bulbs. For spot or down lights, a special lens is normally used, which will either narrow or widen the beam. It is possible now to get LED spotlights with beam angles from 25 to 60 degrees. The lens is either incorporated into the LED package or is added on during final assembly of the spot light. For more conventional lighting, companies often use either a special cover that helps to spread the light out more evenly, making it look more like a frosted incandescent bulb. Another method is to use what is commonly called a "corn
cob light," which resembles a corn cob on which a frosted or clear cover had been added to give the bulb a more traditional appearance.
It is now possible to use LED lighting for entire rooms. My bathroom uses LED spot lights. All of our outside lights are now LED, (except for one so clients can see there is no difference between conventional and LED). And our kitchen will soon be all LED lighting.

Q. Another LED myth is that the lamps only emit very cool light, which isn't always flattering or inviting in the home. How has the color output of LEDs changed recently?A. While this is still true, to a certain extent, it is now possible to get warm white or cool white LEDs. True white LEDs are still a bit of a holy grail for LED manufacturers. Virtually all white LEDs are actually blue LEDs with a special phosphor coating which converts the blue light to white, hence the cold light from white LEDs. Warm white LEDs have a slightly different phosphor coating and produce a light that is more like a conventional bulb. I think that these days, standard warm white LED bulbs are pretty good.
Other methods to produce or improve the white light include:
  • Using an RGB LED. When the red, green and blue are fully on, this produces a white light. The good thing about this method is that you can fine-tune the light to give you the exact type of white light. Problems with this method are sometimes it is possible to get a nice white spot, but the edges of the beam can appear as other colors, and the beam angle can be very small. Brightness has been an issue but this is steadily improving.
  • Using an amber LED with the white/warm white LEDs. This has its own problems, too, as the optics for the LEDs need to be able to mix the light together, otherwise you get a nice warm patch, a yellow patch and a white patch. Not very nice.
  • Mixing warm white and cold white LED bulbs or modules. This can be done either by having every other bulb in a room as cold white and the others as warm white, (I've done this in our bathroom). Or use warm white and cold white LED modules and a special dimmer controller to mix the two together.

Q. The kitchen is one of the easiest rooms in which to incorporate LEDs in the home. What are some creative lighting applications for this space?A. Have a look at the lenses for LEDs in WSRM--- CATALOGUE2013. Also consider under-cabinet lighting; we recently related a Youtube video to explain WSRM's company and products.
Q. LEDs can be cost-prohibitive up front. Are they really worth it? How much can the typical homeowner save from switching over to LED lighting and do these lamps eventually pay for themselves?A. The cost isn't that great really. A typical 6W bulb costs a little over $30, and it will last about 10 to 15 years in a normal house. If we assume that, for purposes of calculation, 1kWh costs $0.10, and the light is used for 6 hours a day we get:
6 x 6 = 36W per day or 0.036kW per day
0.036 x 0.10 = $0.0036 per day to run the light.
So in a year it will cost:
0.0036 x 365 = $1.314 per year
In comparison, a normal 50W halogen bulb will consume:
50 x 6 = 300W or 0.3kW per day
0.3 x 0.1 = $0.03 per day to run
0.03 x 365 = $10.95 per year
Savings per year are:
10.95 - 1.314 = $9.633 per year
Now assume at least a 10 year life span, and the savings will be $96.33 over the life of the bulb. In the same time you will have had to change the halogen bulb at least (assuming a 2000 hour life span) 10 times at a cost of at least $2.50 per bulb. This means a savings of at least another $25.00 over the lifespan of the LED bulb.

Q. Many LED light fixtures have that tell-tale look. What new styles are available, and how do they rate in terms of aesthetics compared to incandescent fixtures on the market?A. This is changing, and I also think we will see more creative lighting fixtures. Since LEDs have a long life span, it is now possible to have designs that don't require you to have access to the light source. This is something that will definitely become more popular as LED lighting becomes more mainstream. Some of the bulb designs look like works of modern art in their own right, so we may see designs that show this off.
LED lighting is improving all the time. And it seems to a certain degree that it is following Moores Law (for computing power) in that we are seeing a doubling of light output about every 3 years or so. But what is happening in the lab normally takes a year before we see it ready for public consumption.
Adopting LED lighting now is definitely worth it, since you will be saving money and helping the environment. Benefits of using LED lighting include:
  • Long Life. All the bulbs and tubes we supply last for 50,000 hours-that's over 5 years of continuous use. If you were to use a bulb for 8 hours a day everyday, you would need to change the bulb in about 17 years.
  • Reduced power consumption. LED bulbs are more energy efficient. A 3W LED bulb will replace a 25 to 35W halogen bulb.
  • Reduces your carbon footprint. Reduced energy consumption means a reduction in the amount of CO2 produced.
  • Reduced running and maintenance costs.
  • No UV and little IR. LED lighting produces no ultra-violet (UV) radiation and very little infra-red (IR) radiation, which makes them ideal for display lighting, since they won't cause fading or premature aging.
  • Durable. LEDs contain no filament that can easily be damaged by shocks and vibrations, making them very rugged.
  • Contain no mercury. Unlike compact fluorescents, LEDs contain no mercury, so disposing of them is easier.
  • Wide range of colors. LEDs are available in a wide range of colors. Utilizing RGB LEDs and a special controller, virtually any color combination is possible, allowing greater flexibility in they way things are lit.
  • Virtually instant on. Unlike compact fluorescents, which can take up to a minute to reach full brightness, LEDs come on instantly.
  • No flickering. Something else that many compact fluorescents do is flicker, especially as they get older.
  • On-Off cycling. When CFLs are used in places that have a short on duration such as cupboards and toilets, their life is reduced and in some cases it is actually worse than the incandescent bulb they have replaced.
As you can see, there are many benefits in using LED lighting over traditional and compact fluorescent lighting.
Many thanks to Dr. Shephard for his valuable input on WSRM---LEDlights!



http://zgledn.yglm.mobi/
SALES CONTACT
ITALY
 NETHERLAND
Amsterdam